The saliva (25 µL) and KPT-330 datasheet synovial lubricin (10 µg) sample were then loaded onto a SDS-polyacrylamide/agarose composite gel (0-7%) [6] and SDS-PAGE gel (3-8%) respectively. The SDS-AgPAGE were run in boronate/Tris buffer (192 mM boric acid, 1 mM EDTA, pH adjusted to 7.6 with Tris and 0.1% SDS) and SDS-PAGE were run in Tris acetate buffer (0.1 Inhibitors,research,lifescience,medical M Tricine, 0.1 M Tris pH adjusted to 8.4 and 0.1% SDS) respectively until the dye front ran out of the gel. The gels were blotted to PVDF membranes, stained with alcian blue, and oligosaccharides were released by reductive β-elimination as described previously [6,10]. 3.3. Exoglycosidase Treatment Inhibitors,research,lifescience,medical and Release

of O-Linked Oligosaccharides Oligosaccharide mixture from PGM (10 µg) (Sigma-Aldrich, St Louis, MO, USA) were digested in 0.5 mU jack bean/HEXase III or GUH hexosaminidase or α- N-acetylgalactosaminidase in 10 µL of

reaction buffer for 1h at 37 °C. Purified human synovial lubricin oligosaccharides from synovial Inhibitors,research,lifescience,medical fluid were digested in 0.5 mU sialidase S/NANase I in 10 µL of reaction buffer for 16 h at 37 °C. Salivary mucins (MUC5B and MUC7) blotted onto PVDF membranes after SDS-AgPAGE (Figure 4a) were incubated with fresh saliva and control saliva (saliva boiled for 15 min) for 6 h at 37 °C. For confirmation of linkage specific sialidases, released MUC5B and MUC7 oligosaccharides were digested in 0.5 mU sialidase S/NANase I in 10 µL of reaction buffer for 16h at 37 °C Salivary mucin oligosaccharides were released for exoglycosidase Inhibitors,research,lifescience,medical activity LC-MS monitoring by reductive β-elimination as described previously [6,10]. Monitoring of exoglycosidase using already released oligosaccharides

was performed after desalting using graphitized carbon packed in micro zip-tips as described [10]. 3.4. Inhibitors,research,lifescience,medical LC-MS2 and LC-MSn Analysis of Oligosaccharides and Interpretation of Data Sample injection and LC was performed by using a CTC PAL autosampler and LC pump (Agilent, Santa Clara, CA, USA). Oligosaccharides were analyzed by capillary graphitized carbon(10 × 0.25 mm id, 5 µm Hypercarb particles, why Thermo-Hypersil, Runcorn, UK) LC-MS and LC-MS2 in negative ion mode using an LTQ mass spectrometer (Thermo-Fisher, San Jose, CA, USA). Oligosaccharides were eluted with an H20/acetonitrile gradient containing 10 mM NH4HCO3 (0–35% acetonitrile in 45 min, 10 min wash with 100% acetonitrile and 15 min equilibration with 0% acetonitrile). The capillary voltage and the spray voltage for the mass spectrometer were set to 3 V and 2.6 kV respectively and the capillary temperature was set to 300 °C. Air was used as a sheath gas and a full scan ranges from m/z 380 to m/z 2000 were defined for the structures to be analyzed.